Windows 98 Stuck in Safe Mode – Defrag errors out
Name: Mary Helen McEvoy
I have windows 98. My computer is genuine interx86 family 15 model 2 stepping 9 608.0mb ram. Fat 32 with more than 31.gb It will not come out of safe mode. I ran scan disk, etc and it says it has corrected errors, but still will not come out of safe mode. I recently bought a new sound card, inserted it and it worked for a while, but I was having conflicts with the mother board with that sound card. I couldn’t get it to work right, disable, etc. So I finally took the new sound card out. I tried removing programs, etc, even went into Device manager and deleted things relating to the sound card.. I don’t think I should have done that… Now device manager doesn’t show for com port, usb ports…When I try to de frag the hard drive it tells me I have errors that I must fix first. Can you help me? I didn’t have sound for a while, but I got that corrected.
When you say that defrag tells you that you have errors, is it talking about programs accessing the disk while the defragmenter is running, or is it talking about actual errors on your hard disk? Where your computer is most likely at least 7 years old, a hard drive failure is certainly not out of the question.
To check for this, you’ll want to run Scandisk again, but with a couple of flags. Luckily in this case you’re already in Safe Mode, so we won’t have to worry about booting there.
To start Scandisk:
Click Start->Programs->Accessories->Scandisk
Under Check Disk Options be sure to check the following:
- Automatically fix file system errors
- Scan for and attempt recovery of bad sectors
You can also simply run the command line version, in which case you’d click Start->Run and type Scandisk /fix .
It’s been forever since I’ve had to work on a Windows 98 machine, so forgive me if those instructions are a little off.
With any luck Scandisk will locate some bad sectors or whatnot on your drive, repair or move them, and you’ll be able to boot after this with little difficulty. I have a feeling that your hard drive is simply going out on you though, so I have my doubts. A new hard drive may be in your very near future. However, if your Safe Mode trap is due to the items that you removed from the Device Manager, then this could get a lot more tricky.
You mention that the soundcard had issues with your motherboard, but then later mention that the sound is now working. Were you able to get the soundcard that you bought functioning, or does your mother board have onboard sound that’s being used?
If the new soundcard is in the machine, then take it out. Try to boot with it removed and see what happens. IRQ conflicts are common on older machines and this may be what’s causing your computer to get stuck in Safe Mode. Your machine tries to initialize all the hardware and ends up with the conflict between the sound card and whatever else, so it reverts to safe mode so the problem can be fixed.
If that doesn’t work, then you may be forced to reinstall Windows. I’ve no way of knowing exactly what was removed from the device manager and as such couldn’t really explain how to get those items back up and running.
Do keep in mind that unless you do your reinstall of Windows without formatting the drive, all data on it would be lost. If you decide to go this route, you’ll definitely need to back up all of your data and be sure to locate any application CDs as the programs will need to be reinstalled.
You can, of course, take your computer to someone to be looked at. I always have a hard time recommending that with a machine so old as it is generally just not worth sinking any money into. You can buy a new Dell desktop that’s OK for most tasks for around $500. Assuming my suggestions above didn’t work, then you may consider just getting a new system. You can always hook up the old computer’s hard drive to the new machine and get your data off of it. Photos, music, documents, etc are all very easy to copy over if you know where they’re saved.
Anyway, if any of the suggestions do end up working for you then please come back and let us know which one did.
Popularity: 1% [?]

Tweet This
Share on Facebook
Digg This
Save to delicious
Stumble it
RSS Feed
Just wanted to write and let you know I appreciated your immediate response. I redid everything..I also had installed a tape deck in the system, when I took that out, inserted my windows 98 disk rebooted and installed that, everything is fine. I have windows 98 for my embroidery work…and I definitely will not mess with that again. I am going out and buying a new/used system for my recording of records and tapes..what a mess that was. Thank you for being there.
Mary
Hi – Now I have another problem…. Bought a used dell Optiplex GX270 series, Bios version A01..professional xp 3 ghz, 1gb ram, 120 gbhd open office, antivirus last week. I used it for a couple of days, bought a modem for it.. installed it and it worked fine. I then tried to put my plusdeck2c in, it had 2 dvd’s in the bays, no room for the plusdeck, so I removed one dvd and inserted the tape deck in the bay, put everything back together, plugged it in and got a message that the primary hard drive could not be found.. I checked all the leads, cables, unplugged and plugged back in so that every connection was secure.. Same thing came back on the monitor can’t find .. So I then took everything back out that I had put in.. No luck. Now it says Secondary drive 0 and Secondary drive 1 not found. and wants me to go to F2 to run the setup utility. What now???
Please help.
make sure that pin 1 on the drives matches pin 1 with the EIDE cables. The EIDE cables look like a gray ribbon of little, glued together, cables with 1 red wire. The red wire has to match pin 1 on the back of the drive. Make sure that the primary 0 is set to master and that the primary 1 is set to slave. you can tell by looking at the jumper at the back of the drive. It should correspond with a graph that is usually in the manual of the drive or on the drive itself. the jumper is a little plastic cover that has a metal wire in the inside, you may have to use tweezers to remove it and put it in the right place. also make sure that the secondary o is set to master and the secondary 1 is set to slave using the same method. if there isn’t a drive that goes into the slave than you don’t have to bother plugging one in and setting it to slave. just make sure the one by itself is set to master.